On this page, cookies are needed if you want to use the full range of the page. Please activate cookies and refresh that page. After refresh a cookie management dialogs will be available.

The cookie settings on this website are set to 'allow only strictly necessary' to give you the very best experience. If you continue without changing these settings, you consent to this - but if you want, you can change your settings at any time at the bottom of this page. Our cookie policy

 

Interface Modules


 
B201 2-Wire Powered Loop
  • Suitable for use with 2-wire smoke detectors and burglary devices
  • Supports up to 20 compatible smoke detectors
  • Resets latching devices from the control panel
  • Connects to the control panel terminal block with easy-to-install integrated pins
 
 
B810 RECEIVER-SDI2
  • Dual internal antennas provide spatial and polar RF signal reception for high reliability
  • Cover and wall tamper protection
  • Multiple device enrollment options as well as RF diagnostics ensure efficient and effective installation
  • Supports supervision of wireless points (504), keyfobs (1000), and repeaters (8)
  • External status LEDs
  • Detection and reporting of radio frequency interference
 

Features

BubbleLevel EasyInstall Indoor SDI2 Wireless
 
 
B426 Ethernet Communication Module
  • Full two-way IP event reporting with remote control panel programming support
  • 10/100 Base-T Ethernet communication for IPv6 and IPv4 networks
  • NIST-FIPS197 Certified for 128-bit to 256-bitAES Encrypted Line Security
  • Plug and Play installation, including UPnP service to enable remote programming behind firewalls
  • Advanced configuration by browser, RPS, or A-Link
 
 
B430 Plug-in Communicator, Telephone
  • Provides a single telephone line with RJ-45 connection for central station reporting and remote programming
  • Easily configured for communications from Remote Programming Software (RPS) or a keypad, eliminating the need for separate configuration
  • Easy two-step plug-in installation, troubleshooting, and maintenance
 
 
C900V2 Dialer intercept communicator, Ethernet
  • Captures alarm and event data from dialer-based control panels using CONTACT ID, SIA, Modem II, Modem IIe, Modem IIIa2, Pulse, and other formats
  • Performs full data transmissions without changing the data
  • 12 VDC to 24 VDC voltage range
  • Re-routes signals using UDP/IP-based data networks
  • Convenient connection (RJ-45 Jack) to Ethernet networks
  • Integrated 10/100 Network Interface Module, or NIM
  • Provides acknowledgement from the receiver to the control panel
  • Supports 128-bit AES Rijndael encryption
 
 
D113 Supervision module, battery lead
  • Works with 12 V nominal systems
  • Meets NFPA 72 requirements for battery lead supervision for fire alarm control panels (FACPs)
 
 
D125B Initiating module, dual class B, 12/24V
  • Two separate powered detector loops
  • Suitable for 12 VDC or 24 VDC, two‑wire or four‑wire detectors
  • Up to 50 two‑wire 12 VDC glass break detectors
  • Reports individual loop alarm, individual loop trouble, and ground fault
  • Manually resets latching devices from control panel or remote central station
 
 
D129 Initiating circuit module, dual class A
  • Adjustable alarm and reset delays
  • Provides two supervised Class A (Style D) loops
  • Reliable terminal connections
  • Suitable for waterflow switches
  • Compensates for sprinkler alarm valve fanning
  • Suitable for mechanical initiating devices
 
 
D135A Low battery disconnect module
  • Disconnects a B6512/B5512/B4512/B3512 from the battery when the battery level drops to 9.5 VDC
  • Required for use with compatible control panels for CAN/ULC S559
  • Quick and easy installation
 
 
D8125MUX Expansion module, Multiplex
  • Multiplex bus controls two independent buses
  • Aux Power terminals that can be used for remote devices
  • Programmed with D5060 Handheld Programmer (not required for "i" class modules)
  • Operation monitoring LED
  • Connect to Zonex 1 or Zonex 2
  • Standard three hole mounting
  • Accepts Daisy Chain and T-Tapping bus configurations
 
 
D8130 Door release module
  • Two Form C (5 A rated) contacts
  • Remotely controls fire system devices
  • Instant or delayed relay activation and restoral
  • Relay closure follows indicating circuit duration
  • Disable switch supervised for system testing
 
 
DX4010V2 USB/serial interface module
  • RS-232/USB connectivity
  • Enhanced direct connection for Remote Programming Software (RPS)
  • RJ-16 data bus
  • Transparent enclosure
  • Diagnostic light emitting diodes (LEDs)
  • DIP switches for address and bus programming
 
 
ITS-DX4020-G GPRS/GSM integrated communicator
  • Secure IP communication from compatible Bosch panels to Bosch receivers
  • Remote programming of IP compatible Bosch panels
  • GSM reporting from Contact ID control panels to any PSTN receiver
  • Easy provisioning using SMS (text) or USB
  • Easy installation, troubleshooting, and maintenance
 
 
MODEM-KIT-2400B Programming modem, 2400 baud
  • For programming communications